hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } 2.2.15pre4

[Douglas F.Elznic]

I have been getting the following errors since I upgraded to 2.2.15pre4. 
I do not think that I configured anything different this time around. I can not
figure out what if there is something in particular that causes this error.

hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: DMA disabled
hdb: DMA disabled  
ide0: reset: success:                                                         

I am running:
Linux calvert 2.2.15pre4 #2 Mon Jan 24 18:02:46 EST 2000 i686 unknown
Kernel modules         2.1.121
Gnu C                  2.95.2
Binutils               2.9.5.0.16
Linux C Library        2.1.2
Dynamic linker         ldd (GNU libc) 2.1.2
Procps                 2.0.6
Mount                  2.9y
Net-tools              1.53
Console-tools          0.2.2
Sh-utils               2.0
Modules Loaded         vfat fat                                                                                
With hda and hdb being:
[root en calvert linux]# hdparm -vi /dev/hda

/dev/hda:
 multcount    =  0 (off)
 I/O support  =  0 (default 16-bit)
 unmaskirq    =  0 (off)
 using_dma    =  0 (off)
 keepsettings =  0 (off)
 nowerr       =  0 (off)
 readonly     =  0 (off)
 readahead    =  8 (on)
 geometry     = 1401/255/63, sectors = 22510656, start = 0
 
 Model=Maxtor 91152D8, FwRev=WAS82739, SerialNo=K806FPDA
 Config={ Fixed }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=29
 BuffType=3(DualPortCache), BuffSize=256kB, MaxMultSect=16, MultSect=off
 DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=2(fast)
 
 tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
 UDMA modes: mode0 mode1 *mode2
 Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4
 
[root en calvert linux]# hdparm -vi /dev/hdb
 
/dev/hdb:
 multcount    =  0 (off)
 I/O support  =  0 (default 16-bit)
 unmaskirq    =  0 (off)
 using_dma    =  0 (off)
 keepsettings =  0 (off)
 nowerr       =  0 (off)
 readonly     =  0 (off)
 readahead    =  8 (on)
 geometry     = 3739/255/63, sectors = 60074784, start = 0
 
 Model=WDC WD307AA, FwRev=05.05B05, SerialNo=WD-WMA111025946
 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
 RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
 BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=off
 DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=0(slow)
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=60074784
 WARNING 43560720 ORPHANED SECTORS :: KERNEL REPORTING ERROR
 tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
 UDMA modes: mode0 mode1 *mode2 mode3 mode4
 Drive Supports : ATA-1 ATA-2 ATA-3 ATA-4                  
                              
lspci reports my ide controller being a:
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
        Flags: bus master, medium devsel, latency 64
        I/O ports at 1000


     -- 
--
Douglas F. Elznic
<dfelznic @ syr.edu>

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo en vger.rutgers.edu
Please read the FAQ at http://www.tux.org/lkml/